You can view the full version and download it in PDF format.
Page 5 of 23
This section must be read before any connection is made to the mains
Do not expose the equipment to rain or moisture.
Do not remove the cover from the equipment.
Do not push anything inside the equipment through the
Do not handle the mains lead with wet hands.
EQUIPMENT MAINS WORKING SETTING
Your Marantz product has been prepared to comply with the
household power and safety requirements that exist in your area.
SR2100 can be powered by 230 V AC only.
IMPORTANT: (FOR UK VERSION)
This apparatus is fitted with an approved moulded 13 Amp plug.
To change a fuse in this type of plug proceed as follows:
Remove fuse cover and fuse.
Fix new fuse which should be a BS1362 13A, A.S.T.A. or BSI
Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 13A.
If a plug without a fuse is used, the fuse at the distribution board
should not be greater than 5A.
The severed plug must be destroyed to avoid a possible shock
hazard should it be inserted into a 13A socket elsewhere.
HOW TO CONNECT A PLUG
The wires in the mains lead are coloured in accordance with the
The BLUE wire must be connected to the terminal which is
marked with the letter “N” or coloured BLACK.
The BROWN wire must be connected to the terminal which is
marked with the letter “L” or coloured RED.
Do not connect either wires to the earth terminal in the plug which
is marked by the letter “E” or by the safety earth symbol
coloured green or green and yellow.
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead — not simply over the two wires.
Recording and playback of any material may require consent. For
further information refer to the following:
Copyright Act 1956
Dramatic and Musical Performers Act 1958
Performers Protection Acts 1963 and 1972
any subsequent statutory enactments and orders
ABOUT THIS USER GUIDE
Refer to the figures on page iv of this user guide. The numbers on the
figures correspond to those in the text. All references to the
connections and controls that are printed in
type are as they
appear on the unit.
The following precautions should be taken when operating the
When siting the equipment ensure that:
the ventilation holes are not covered;
air is allowed to circulate freely around the equipment
it is on a vibration free surface;
it will not be exposed to interference from an external source;
it will not be exposed to excessive heat, cold, moisture or dust;
it will not be exposed to direct sunlight;
it will not be exposed to electrostatic discharges
Never place heavy objects on the equipment.
If a foreign body or water does enter the equipment, contact your
nearest dealer or service centre.
Do not pull out the plug by pulling on the mains lead, hold the plug.
It is advisable when leaving the house, or during a thunderstorm, to
disconnect the equipment from the mains supply.
Easy operation with remote control bus in SYSTEM mode operation
Top end model of the Marantz AV system
This model has a very slim shape and a height of 68 mm. All
buttons, with the exception of the power and door open/close
buttons, are concealed behind a front flap.
High power output of 50W + 50W (DIN, into 8 ohms)
The discrete configuration possesses a high level of reliability.
Door open/close mechanism operate both by switch and remote
50 Station random preset tuner
Station names consisting of 8 characters can be stored together
with the frequencies.
RDS (Radio Data System) compatibility
PTY (Programme Type) Auto Seek
PS (Programme Service name) Display
TA (Traffic Announcement) Seek
TP (Traffic Programme) Seek
EON (Enhanced Other Network) Seek for TA and NEWS
Independent/System operation switch
This unit can be operated as a system component in combination
with the CD R and DVD players from the Marantz AV system.
3 Program Timer/Sleep Timer
Stylish New LCD (Liquid Crystal Display) Panel with Backlight
The New LCD panel backlight can be controlled with dimmer