NAD T 758 user manual download (Page 9 of 44)

Languages: English
Pages:44
Description:A/V рессивер
You can view the full version and download it in PDF format.
Page 9 of 44
5
IR IN/IR OUT 1-2
These mini-jacks accept and output remote-controlled codes in
electrical format, using industry-standard protocols, for use with “IR-
repeater” and multi-room systems and related technologies.
All NAD products with IR IN/IR OUT features are fully compatible
with the T 758. For non-NAD models, please check with your other
product’s service specialists as to their compatibility to the T 758’s IR
features.
IR IN
This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the T 758 from a remote location.
IR OUT 1, IR OUT 2
When connected to the IR IN of an ancillary equipment, direct the
ancillary equipment’s own remote control to the T 758’s infrared
receiver to command or control the linked unit.
IR IN and IR OUT 1, IR OUT 2
Connect the T 758’s IR IN to the IR OUT of an ancillary equipment.
Connect also the T 758’s IR OUT 1 to another equipment with IR IN
feature. With this setup, the T 758 acts as an “IR-repeater” allowing the
equipment connected to the T 758’s IR IN control or command of the
other equipment linked to the T 758’s IR OUT 1. A combination of IR IN
and IR OUT 2 also perform the same function.
6
+12V TRIGGER OUT
The +12V TRIGGER OUT is used for controlling external equipment that
is equipped with a +12V trigger input.
Connect this +12V TRIGGER OUT to the other equipment’s
corresponding +12V DC input jack using a mono cable with 3.5mm
male plug.
This output will be 12V when the T 758 is ON and 0V when it is shut
down or at standby mode.
7
MP DOCK
The T 758 is equipped with a data port in the rear panel where an
optional NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later
variants can be plugged in.
Connect the MP DOCK (DATA PORT) jack of the T 758 to the
corresponding DATA PORT socket of the optional NAD IPD model.
AUDIO 3 and S-VIDEO 1 are the assigned default ports for the audio/
video output of the separately sold NAD IPD (NAD IPD Dock for
iPod) 1, NAD IPD 2 and later variants.
Refer also to the LISTENING TO YOUR iPod PLAYER segment of the
OPERATION section.
NOTE
The NAD IPD Dock for iPod is not supplied with your T 758.
8
DAB MODULE INPUT ±230V version model only²
The T 758 is compatible only with the NAD DAB Adaptor module
models DB 1 or DB 2.
Plug-in the other end of the Mini-Din connector from the NAD DAB
Adaptor module output port into this socket.
With DAB, you can receive CD-like quality programs without any
annoying interference and signal distortion.
Refer also to the LISTENING TO DAB RADIO segment of the
OPERATION section.
9
RS 232
NAD is a certified partner of AMX and Crestron and fully supports
these external devices. Check out the NAD website for information
about AMX and Crestron compatibility with NAD.
See your NAD audio
specialist for more information.
Connect this interface using RS-232 serial cable (not supplied) to
any Windows compatible PC to allow remote control of the T 758
via compatible external controllers.
Refer to the NAD website for information about RS232 Protocol
documents and PC interface program.
10 MONITOR
Connect to the video input of a monitor/television using quality
composite video cable.
VIDEO 1-2/S-VIDEO
Connect these composite video and S-video input ports to the
corresponding video output ports of source components such as
DVD players, cable/satellite boxes or other compatible line level video
sources.
11 AC MAINS INPUT
The T 758 comes supplied with a separate detachable mains power
cord.
Before connecting the plug to the mains power source,
ensure that it is firmly connected to the T 758’s AC Mains input
socket first.
Always disconnect the mains power plug from the mains power
source first, before disconnecting the cable from the T 758’s AC
Mains input socket.
12 SWITCHED AC OUTLET
This convenience outlet can supply switched power to another
component or accessory.
The total draw of all devices connected to this outlet must not
exceed 100 watts.
It is powered ON and OFF by the front panel STANDBY button or by
the AVR 4’s ON and OFF buttons.
13 7.1 CHANNEL INPUT
Connect to the corresponding analog audio output of a
multichannel source component such as a DVD-Audio or
multichannel-SACD player or external multichannel decoder (disc
copy protected formats only allow analog signal transfer). Typically,
these sources will produce 5.1-channel output, in which case the
Surround Back jacks are left unconnected. The signal present at
these jacks can be heard by selecting Source 7 (7.1 CHANNEL INPUT
is defaulted to this Source).
There is no bass-management or other processing (other than
master-volume control) available to this 7.1 channel input.
While the multichannel audio output of a DVD/BD player can be
connected to these jacks, using the T 758’s own Dolby Digital and
DTS decoding and digital-analog converters via a digital connection
will usually produce superior results.
IDENTIFICATION OF CONTROLS
REAR PANEL
9
ENGLISH
PORTUGUÊS
FRANÇAIS
ESPAÑOL
ITALIANO
DEUTSCH
NEDERLANDS
SVENSKA
РУССКИЙ
Sample
This manual is suitable for devices