Jenn-Air JB36NXFXLW00 user manual download (Page 5 of 52)

Integrated

Installation

-

Full Height

Grille

To remove

the top grille panel:

1.

Open the door(s).

2.

Slide your fingers under the bottom

of the grille panel until

you can fully grasp the panel, then pull the panel straight

out.

Place the grille panel on a soft surface.

To replace

the

top grille

panel:

1.

Align the bracket with the mounting

posts.

2.

Push the grille panel forward

until the bracket snaps into

place.

Power

On or Off Switch

1.

Remove

the top grille panel.

2.

Press power switch

to the On or Off position.

3.

Replace the top grille panel.

IMPORTANT:

Be sure the power switch

is set to the On position

after cleaning

refrigerator

or changing

light bulbs.

/

[]

J

A

A. Power

switch

Read all directions

before you begin.

IMPORTANT:

•

When your refrigerator

was installed,

the water connection

from the water source should

have been connected

to your

refrigerator.

If your refrigerator

is not connected

to a water

source, see "Connect

to Water Line" in the Installation

Instructions.

If you have any questions

about your water

connection,

see "Troubleshooting"

or call a licensed,

qualified

plumber.

•

If you turn the refrigerator

on before the water line is

connected,

turn the ice maker OFE See "Ice Maker and

Storage

Bin."

•

All installations

must meet local plumbing

code requirements.

Water

Pressure

A cold water supply

with

water pressure

between 30 and 120 psi

(207 and 827 kPa) is required to operate

the water dispenser

and

ice maker. If you have questions

about your water pressure, see

"Troubleshooting"

or call a licensed,

qualified

plumber.

Reverse

Osmosis

Water

Supply

IMPORTANT:

The pressure

of the water supply

coming

out of a

reverse osmosis system

going to the water

inlet valve of the

refrigerator

needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration

system

is connected

to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum

of 40 psi (276 kPa).

If the water

pressure to the reverse osmosis

system is less than

40 psi (276 kPa):

•

Check to see whether

the sediment

filter in the reverse

osmosis

system is blocked.

Replace the filter if necessary.

•

Allow the storage tank on the reverse osmosis

system to refill

after heavy usage.

•

If your refrigerator

has a water filter, it may further

reduce the

water pressure

when used in conjunction

with a reverse

osmosis

system.

Remove the water filter. See "Water

Filtration

System."

If you have questions

about your water

pressure, call a licensed,

qualified

plumber.

Please read before using the water system.

Immediately

after installation,

follow the steps

below to make

sure that the water system

is properly

cleaned.

1.

Turn off the ice maker. Slide the ice maker

On/Off control,

located

on the left-hand

side of the ice bin, to the OFF (down)

position

as shown.

A.

On/Off

control

NOTE: If your model has a base grille water filter, make sure the

water filter is properly

installed

so that the Eject button is out. See

"Water

Filtration

System."

Do not use with water that is microbiologically

unsafe or of

unknown

quality

without adequate

disinfection

before or

after the system.

2=

Turn on the ice maker. Slide the ice maker On/Off

control,

located

on the left-hand

side of the ice bin, to the ON (up)

position.

Please refer to "Ice Maker

and Storage

Bin" for

further

instructions

on the operation

of your ice maker.

•

Allow 24 hours to produce

the first batch of ice.

•

Discard

the first three batches

of ice produced.