Gladiator GARF19XXPK01 user manual download (Page 6 of 20)

Languages:	English
Pages:	20

You can view the full version and download it in PDF format.

1

2

3

4

5

6

7

8

9

Page 6 of 20

NOTE:

If you

have the casters

installed

on your

refrigerator,

the

leveling

screws

will

not work

Shims

can be placed

under

the casters

to level a refrigerator

that

has casters

installed.

Door Closing

Your refrigerator

has two

front

adjustable

rollers

- one on the

right

and one

on the

left. If your

refrigerator

seems

unsteady

or you want

the doors

to close

easier, adjust

the refrigerator's

tilt using

the

instructions

below:

1.

Remove

the

base grille

See Base Grille

graphic.

The two

leveling

screws

are part of the

front

roller

assemblies

which

are at the

base

of the

refrigerator

on either

side.

2.

Use a screwdriver

to adjust

the

leveling

screws.

Turn the leveling

screw

to

the right

to raise

that

side

of the

refrigerator

or turn the

leveling

screw

to

the left to lower

that

side.

It may take several

turns

of the

leveling

screws

to adjust

the

tilt of the

refrigerator.

NOTE:

Having

someone

push

against

the

top

of the

refrigerator

takes

some

weight

off the leveling

screws

and rollers.

This makes

it easier

to adjust

the

screws.

3.

Open

both

doors

again

and

check

to make

sure that

they

close

as easily

as you

like. If not, tilt the refrigerator

slightly

more

to the

rear by turning

both

leveling

screws

to the

right.

It may take

several

more

turns,

and you should

turn

both

leveling

screws

the

same

amount

4.

Replace

the

base grille.

Door Alignment

If tile

space

between

your

doors

looks

uneven,

you can adjust

it

using

the instructions

below:

1.

Pry off the top

hinge

cover.

2.

Loosen

the top

hinge

screws

using

a 5/_6"socket

or wrench.

3.

Have

someone

hold

the

door

in place

or put a spacer

between

the doors

while

you tighten

the top

hinge screws.

4.

Replace

the

top

hinge

cover.

Gather

the required

tools

and

parts

before

starting

installation.

TOOLS

NEEDED:

•

Y¢' Socket

wrench

or nut

•

%"

Socket

wrench

or nut

driver

driver

•

V2"

Wrench

PARTS

SUPPLIED:

•

Rigid

Casters

(2)

•

V4--20

x I_A" Self-tapping

•

Swivel

Casters

(2)

hex-head

bolts

(4)

•

5/_6--18 Self-locking

•

_/4--20 x I_A " lock

hex-nuts

(16)

washers

(4)

•

5_%_18 x z/8" Hex-head

•

Caster

brackets

(located

in

bolts

(16)

FeaturePak)

(2)

•

Plastic

skids(shipped

with

the

refrigerator)

1.

Before

you

begin,

turn

the refrigerator

control

OFE

2.

Unplug

refrigerator

or disconnect

power.

3.

Remove

food

and

any adjustable

shelves

and

bins

from

refrigerator.

4.

Open

the

lower

compartment

door

and

remove

the

base grille.

Remove

the grille

by grasping

the grille

with

both

hands,

lifting

up

and

pulling

bottom

of the grille

toward

you.

5.

Place

the

plastic

skids

(shipped

with

the refrigerator)

on the floor

at least

3 ft (91.44

cm)

apart.

Lay a piece

of cardboard

or other

protective

material

over the

skids.

This will

elevate

the

refrigerator

to allow

for easier

caster

installation

and

also

protect

it from

scratches.

NOTE:

If the

skids

have

been

discarded

or are not

available,

2" x 4" boards

may

be used.

6.

Place

the

refrigerator

on its side

on top

of the

cardboard

or

protective

material.

Make

sure

the door

hinge

is facing

upward.

IMPORTANT:

It is important

that

the door

hinge face

upward

during

the

entire

caster

installation.

B

A. Top hinge

B. Center hinge

6

Sample

This manual is suitable for devices