Gladiator GARF19XXPK01 user manual download (Page 7 of 36)

Languages: English
Pages:36
You can view the full version and download it in PDF format.
Page 7 of 36
NOTE:
If you
have the casters
installed
on your
refrigerator,
the
leveling
screws
will
not work.
Shims
can be placed
under
the casters
to level a refrigerator
that
has casters
installed.
Door Closing
Your refrigerator
has two
front
adjustable
rollers
- one on the
right
and one
on the left.
If your
refrigerator
seems
unsteady
or you
want
the doors
to close
easier, adjust
the refrigerator's
tilt using
the
instructions
below:
1.
Remove
the
base grille.
See Base Grille
graphic.
The two
leveling
screws
are part
of the
front
roller
assemblies
which
are at the
base
of the
refrigerator
on either
side.
2.
Use a screwdriver
to adjust
the
leveling
screws.
Turn the
leveling
screw
to the right
to raise
that
side
of the
refrigerator
or turn the
leveling
screw
to the left to lower
that
side.
It may take
several
turns
of the
leveling
screws
to adjust
the
tilt of the
refrigerator.
NOTE:
Having
someone
push
against
the
top
of the refrigerator
takes
some weight
off the leveling
screws
and rollers.
This makes
it easier
to adjust
the
screws.
PARTS
SUPPLIED:
Rigid
Casters
(2)
Swivel
Casters
(2)
5/16--18 Self-locking
hex-nuts
(16)
5/16--18 x %" Hex-head
bolts
(16)
1¼--20
x 1V4" Self-tapping
hex-head
bolts
(4)
1A--20
x 1V4" lock
washers
(4)
Caster
brackets
(located
in
FeaturePak)
(2)
Plastic
skids
(shipped
with
the
refrigerator)
1.
Before
you
begin,
turn
the refrigerator
control
OFR
2.
Unplug
refrigerator
or disconnect
power.
3.
Remove
food
and
any adjustable
shelves
and
bins from
refrigerator.
4.
Open
the
lower
compartment
door
and
remove
the
base grille.
Remove
the grille
by grasping
the grille
with
both
hands,
lifting
up
and
pulling
bottom
of the
grille
toward
you.
5.
Place
the
plastic
skids
(shipped
with
the refrigerator)
on the floor
at least
3 ft (91.44
cm)
apart.
Lay a piece
of cardboard
or other
protective
material
over
the
skids.
This will
elevate
the
refrigerator
to allow
for easier
caster
installation
and
also
protect
it from
scratches.
NOTE:
If the
skids
have
been
discarded
or are not
available,
2" x 4" boards
may
be used.
6.
Place
the
refrigerator
on its side
on top
of the cardboard
or
protective
material.
Make
sure
the door
hinge
is facing
upward.
IMPORTANT:
It is important
that
the door
hinge face
upward
during
the
entire
caster
installation.
3.
Open
both
doors
again
and
check
to make
sure
that they
close
as easily
as you
like. If not, tilt the refrigerator
slightly
more
to the
rear by turning
both
leveling
screws
to the
right.
It may take
several
more
turns,
and you should
turn both
leveling
screws
the
same
amount.
4.
Replace
the
base grille.
Door Alignment
If the space
between
your
doors
looks
uneven,
you
can adjust
it
using
the instructions
below:
1.
Pry off the top
hinge
cover.
2.
Loosen
the top
hinge
screws
using
a 5/16"socket
or wrench.
3.
Have
someone
hold
the door
in place
or put a spacer
between
the doors
while
you tighten
the top
hinge
screws.
4.
Replace
the
top
hinge
cover.
A. Top hinge
B. Center hinge
7.
Remove
the casters
and
fasteners
from
the box.
8.
Locate
and
remove
the caster
brackets
from the
FeaturePak.
9.
Using
5/16--18 x %" hex-head
bolts,
attach
one
rigid caster
and
one
swivel
caster
to each caster
bracket.
The rigid caster
fits the
front
of the bracket
and the
swivel
caster
fits
on the
rear.
Excessive
Weight
Hazard
Use
two
or more
people
to move
and
install
refrigerator.
Failure
to
do so can
result
in back
or other
injury.
Gather
the required
tools
and
parts
before
starting
installation.
TOOLS
NEEDED:
V2"
Socket
wrench
or nut
3/8" Socket
wrench
or nut
driver
driver
W'
Wrench
Sample
This manual is suitable for devices