Hotpoint HTR17BBBHRCC user manual download

For Devices:Hotpoint HTR17BBBHRCC   and 303 more
Languages:English
Pages:24
You can view the full version and download it in PDF format.
Page 7 of 24
About storage drawer and cover removal,
ge.com
Not aft features
are on aft models.
Humidity
Control
HIGH
LOW
Adjustable Humidity Drawer
(onsomemodels)
Slide the
control
all die way to the
Slide the control
all die way to the
LOW
HIGH
setting
to provide
high
humidity
setting
to provide
lower humidity
levels
recommended
for most vegetables,
recommended
for most fl_uits.
Drawer
and Cover Removal
Drawers
can be removed
easily by grasping
the sides and
lifting
up slighdy while
pulling
drawers
past tile stop location.
i
Full-Width
Drawer
with
Plastic
Cover
Toremovethe cover,
lift it off its supports,
pull
it forward,
tilt it and
take
it out.
!iii
/iii
7
¸
:i;i •_
....
Twin Drawer
Shelf
Toremove:
[-'7]Remove
tile dxmvers.
F_-]Reach in, push
the flont
of glass cover
up, and
at the same time, pull it forward
_tsfar as it will come.
Tilt it and take it out. Avoid cleaning the cold
glass covet"with hot water becmlse the exu'eme
temperature
difference
mW cause it m break.
_]
Remove
tile drawer
flmne.
(Always
remove
tile ,glasscover before
you rake
out the drawer
flame.)
iJfi the fi'mne off the supports at each side
aud back, pull it forward, flit it aud take it out.
Toreplace:
[-_ Lower tile frame
until it rests
(m
tile
supports
at each side and
back.
F_--]
Replace
tile glass covei, pushing
its rear
edge firmly into the rear flvmm channel
and gendy
lowedng
tile flont
into
place.
[j]
Replace
tile (hmve_s.
About the automatic icemaker.
A newly-installed
refrigerator
may take 12to 24 hours to begin making ice.
There are 2 types of icemakers:
Power Switih
]cemaier
GreenPowerLight
FeelerArm
Power switch model
FeelerArmin
the
STOP
FeelerArm
in
(up) position
the
ON
(down)
position
Feeler armmodel
Automatic
Icemaker
(onsomemodels)
The icemaker will produce
approximately
100-130 cubes in a 24-hour period,
depending
on the fl'eezer compai'unent
temperature,
room temperature,
number
of
door openings mid other rise conditions.
If the refl'igeramr
is operamd
before the water
connection
is made to the icemaket; move the
feeler m'm to the
STOP
(.p)
position.
When the refligeramr
has been
connecmd
m the wamr supply, move the feeler am1 m
the ON (down)
position.
The icemaker willfill with water when it cools
to 15°E A newly-installed refi'igerator
mW rake
12 m 24 hours to begin making ice cubes.
Once
the icemaker
starts m make ice,
it mW take up m 48 hours
m fill the bin,
depending
on the mmperamre
setdngs
and
number
of door
openings.
You will hear a buzzing
sound
each dine
the icemaker
fills with WamL
Throw
away tile fi[st few batches
of
ice
to allow the water line to cleaL
Be sure nothing
interferes
with tile sweep
of tile feeler arm.
When
die
bin
fills to die
level
of die
feeler
arm,
die
icemaker
will stop
producing
ice.
It is normal
for severed
cubes
m be joined
mgetheL
If ice
is not
used
flequendy,
old
ice cubes
will become
cloudy,
tasm
stale,
shrink
or
fuse
mgetbeL
On
power
switch
models,
the
g_een
power
light
will blink
if ice cubes
get
stuck
in the
icemakeL
To correct
this,
set the
power
switch
m
0
(off)
and
remove
the
cubes.
Set
the
power
switch
m
I (on)
m resm_*
the
icemakeL
Af_er
the
icemaker
h_ts been
turned
on again,
there
will be
a del W of
about
45 minums
before
tile
icemaker
resumes
ope_v_fion.
NOTE: In homeswith lower-than-averagewater
pressure,you
may
hear the icemakercycle
multiple
times when makingonebatch of ice.
Icemaker
Accessory
Kit
If your refi'igerator did not ah'eady come
equipped
with an maomafic icemaker, an
icemaker accessoW kit is available at extra cost.
Check tlle back of tlle refligerator
for
tile specific icemaker
kit needed
for
7
your model.
Sample