Daewoo AD-13 user manual download

Languages: English
Pages:2
You can view the full version and download it in PDF format.
Page 1 of 2
Ventilation System Instructions
Your Over-the-Range microwave oven is designed for adaptation to the following three types of ventilation.
Select the type of
ventilation required for your installation and proceed to the appropriate section.
A. Horizontal Outside Exhaust
Ventilation Director
Your microwave oven is shipped assembled for Horizontal exhaust.(Rear discharge)
Step. 1
(For Recirculation Only)
* Remove the screws for opening the Ventilation Director and save screws.
Step. 2
(For Recirculation Only)
*Roll the Ventilation Director so that the Rear opening area is closed.
*Align the Ventilation Director's Hole A to D and B to C.
*Tighten the screws.
Microwave Oven
Installation Manual
MODEL:
AD13
Introduction
Your Over-the-Range microwave oven comes complete with an installation instruction kit which contains the following three pieces
of information required to install it.
The following is a list of parts you may
need for installing your Over-the-Range
microwave oven. You will find them
packaged inside the microwave cooking
cavity.
Remove
all parts from the oven cavity and
compare them with the parts list and
illustration to be sure that none are
missing
Parts List
1. Lag screws 1/4" x 2" (4 EA )
2. Toggle Bolts 3" ( 2EA )
3. Spring Loaded Toggle Nuts( 2 EA )
4. Cabinet Mounting Bolts 1/4" x 2" ( 2
EA )
5. Washers 3/4" ( 2 EA )
6. Foam Tape ( 2 EA )
7. Top Cabinet Template
8. Grease Filter (1EA)
9. Bottom Mounting Screw 1/2"(2EA)
10. Mounting Hole Cover (1EA)
Tools
The following tools may be needed for
installation of your microwave oven.
Phillips screwdrivers, Electric Drill
Motor, 1/2" & 5/8" Wood Bits & 3/16"
Drill Bit, Saw to cut exhaust opening,
(if needed) or Jig Saw, Tin Snips (if
needed), Pencil , Tape Measure, Paper
Tape & Duct Tape.
I.
This installation instruction booklet,
complete with diagrams on preparing
your cabinets and microwave oven
for installation.
II.
The Top Cabinet Template, used to
locate the power cord clearance hole,
cabinet mounting holes and the
vertical exhaust location.
III. Wall Mounting Plate, used to locate
the mounting plate holes and to locate
the horizontal exhaust location.
Please read all of the instructions
thoroughly before installing your
microwave oven.
NOTE:
IT IS RECOMMENDED THAT TWO
PEOPLE INSTALL THIS PRODUCT.
IMPORTANT:
KEEP INSTRUCTIONS FOR LOCAL
ELECTRICAL INSPECTOR'S USE.
Important Safety Information
Grounding Instructions
This
appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of the electric shock by
providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding
plug. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING -
Improper use of the grounding can result in a risk of electric shock.
This over-the-range oven was designed for use over ranges no wider than 22 inches.
It may be installed over both gas and
electric cooking equipment.
Safety Instructions
This product requires a three prong grounded receptacle.
The
installer must perform a ground continuity check on the power
outlet box before beginning the installation to insure that the
outlet box is properly grounded.
If not properly grounded, or if
the outlet box does not meet the electrical requirements noted,
(under ELECTRICAL REQUIREMENTS), a qualified
electrician should be employed to correct any deficiencies.
Electrical Requirements
Product rating is 120 volts AC, 60 Hertz, 13.0 amps, and 1.40
kilowatts.
This product must be connected to a supply circuit
of the proper voltage and frequency.
Wire size must conform
to the requirements of the National Electric Code or the
prevailing local code for this kilowatt rating.
The power
supply cord and plug should be brought to a separate
20
ampere branch circuit single grounded receptacle.
The outlet
box should be located near the cord entry point.
The outlet box
and supply circuit should be installed by a qualified electrician
and conform to the National Electric Code or the prevailing
local code.
Installation Hardware
Wall Construction
Your Over-the-Range microwave oven should be mounted against and supported by a flat, vertical wall. Wall construction should be
a minimum of 2" x 2" wall studding and 3/8" or more, thick drywall or plaster/ lath.
The oven must be attached to a
minimum of one
2" x 2" wall stud.
For proper installation the wall must be capable of supporting the cabinet load plus a minimum of 100 pounds, (the 50 pound weight
of the microwave oven and load weight allowance of 50 pounds.)
To find studs, use one of the following methods:
I. Stud finder a magnetic device which locates nails.
II. Using a hammer,
tap lightly across the mounting
surface to find a solid sound.
This will indicate a stud
installation. After locating the stud(s), the center can be
found by: Probing the wall with a small nail to find the
edges of the stud and then placing a mark half way
between the edges.
The center of any adjacent studs
should be 16" from this mark.
CAUTION: FOR PERSONAL SAFETY THIS PRODUCT
CANNOT BE INSTALLED TO CABINET
ARRANGEMENT'S SUCH AS AN ISLAND OR A
PENINSULA. IT MUST BE MOUNTED TO BOTH A
TOP CABINET AND A WALL.
Outside ventilation requires HOOD
EXHAUST DUCT.
Read the following carefully.
EXHAUST CONNECTION:
The
hood exhaust has been designed to mate
with a standard 3-1/4" x 10" rectangular
duct.
REAR EXHAUST:
If rear or
horizontal exhaust is to be used, care
should be taken to align exhaust with
space between studs, or wall should be
prepared at the time it is constructed by
leaving enough space between wall
studs to accommodate exhaust.
MAXIMUM DUCT LENGTH:
For
satisfactory air movement, the total
duct length of
3-1/4" x 10" rectangular
should not exceed maximum 1foot.
Hood Exhaust Duct
1. A minimum of 22.2" between wall
hung side cabinets is required for
installation.
Make sure the bottom
edge of the top cabinet is at least 66"
from the floor and 30" from the
cooking surface.
2. If you are going to vent your
microwave oven to the outside, see
exhaust duct preparation.
Mounting Space
or more
from the
floor to the
top of the
microwave
oven
more than
from cooking
surface
66”
30”
22.2”
3/8” Drywall or
Plaster / Lath
16”
2” X 2”
wood stud or
metal stud
(25 gauge or thicker)
Log screws (part #1) must be
installed in these area
Air Director
Rear Exhaust
1
2
3
4
WALL DUCT
A
F
D
C
E
B
Sample
This manual is suitable for devices