Lynx L27 (2006) user manual download (Page 11 of 24)

Languages: English
Pages:24
You can view the full version and download it in PDF format.
Page 11 of 24
L.P. GAS
Grills orificed
for use with
L.P.gas
come equipped
with
an LP hose/
regulator
assembly
for
connec-
tion to a standard
20 lb. L.P.cyl-
inder
(Type 1). All fttings
neces-
sary to attach the hose/regulator
to the grill
are included.
The L.P.
tank
is not
included.
Operating
pressure: 10.0"W.C.
L.P. Tank Requirements
A dented
or
rusty
L.P.tank
may
be
hazardous
and
should
be
checked
by
your
L.R supplier.
Never use a cylinder
with
a dam-
aged
valve.
Always
check
for
leaks after every L.Rtank change
(see page 11).
The
L.R gas
cylinder
must
be
constructed
and
marked
in ac-
cordance
with
the specifications
for
L.R gas cylinders
of the U.S.
Department
of
Transportation
(DOT) and designed
for use with
a Type
1 system
only.
Do
not
change
the
regulator/hose
as-
sembly
from
that
supplied
with
the
unit
or
attempt
to
use
a
5LP-A equipped
regulator/hose
assembly
with
a standard
510
POL tank/valve
assembly.
The
cylinder
must
be provided
with
a shut
off valve
terminating
in
an L.R gas supply
cylinder
valve
outlet
specified,
as applicable,
for connection
Type 1.
Cylinders
must
be
stored
outdoors
in a well-ventilat-
ed
area
out
of
the
reach
of
children.
If
the
appliance
is stored
indoors,
the
L.R
cylinder
must
be
removed
from
the
appliance,
and
stored
outside.
Turn off LP-gas supply at cylinder
when appliance
is not in use.
Fermez
I'alimentation
en GPL
la bouteille
si I'appareil
ne fonc-
donne pas.
The LP-gas supply
cylinder
must
be disconnected
when
this
ap-
pliance
is not in use.
La bouteille
de GPL doit
_tre
d_-
connect_e si cet appareil
ne fonc-
donne pas.
Your
local
L.P.
filling
station
should
be
equipped
with
the
proper
equipment
to
fill
your
tank.
If trading
your
tank
in,
always
ensure
to
obtain
only
Type
1 201b cylinders
with
an
overfill
protection
device.
L.P. Connections
Connect
the 3/8"flare
end of the
L.R hose to the brass adapter
on
the
manifold
(as shown
in fig-
ure 9-1).
Connect
the Regulator
to the tank
(with
the tank
valve
fully
closed).
Although
the flow
of gas is stopped
when the Type
1 system
is disconnected,
you
should
always
turn
the L.R tank
main
valve
off
after
each
use
and during
transport
of the tank
or unit.
Insert the regulator
inlet
into the tank valve and turn
the
black coupler
clockwise
until the
coupler
is tight.
Do
not
over-
tighten
the coupler.
To disconnect
the coupler,
first
make
sure the
main
tank
valve
is turned
off.
Grasp the coupler
and turn
counter
clockwise.
The
inlet will then disengage.
Gas Line Purging
To purge
the L.P.gas line,
make
sure all controls
are in the
OFF
position.
Turn
the
main
tank
valve
on SLOWLY and turn
one
burner
control
valve on the unit
to the "light"
position
(DO NOT
LITE GRILL). Leave control
ON for
about
20 seconds
to
allow
the
air in the system
to
purge. Wait
5 minutes
before
attempting
to
light
the burners.
Do not attempt
lighting
the grill
within
5 minutes
after purging!
L
3/8"
flare fitting
pre-installed
on grill
20 lb. Type
1 L.R
tank
1
Figu re
9-1
-
Typical attachment
to L.P.tank.
hose/regulator
B_LyNX
9
Sample