Lynx L27 (2006) user manual download (Page 10 of 24)

Languages: English
Pages:24
You can view the full version and download it in PDF format.
Page 10 of 24
Gas
Requirements
Hook-up
Your grill
is setup
to
use either
propane
(LP)or natural gas (NAT).
It is very important
that
the
grill
rating
plate
matches
with
your
gas supply.
The rating
plate is located
in one
or more of the following
places:
under the drip tray
• on the
heat shield
behind
the
front
panel
• on the
inside left
cabinet
wall
(most freestanding
grills)
Do
not attempt
to
operate
the
grill on any gas other
than what
the grill
is orificed
for
and what
the
regulator
is set for.
Should
you
need
to
convert
your
grill
for use with
a different
gas type,
a conversion
kit, available
from
your dealer, is required.
Never
connect
an
unregu-
lated
gas line
to the
grill.
so as to calculate what size diam-
eter pipe is needed, for the total
length
of pipe from the gas main
(at house) to grill hook-up.
If the
gas line is too small, the grill will
not function
properly.
In no case
should pipe less than 3/4" dia. be
used to connect
this product.
An
installer-supplied
gas
shut-off
valve
must
be
in-
stalled
in
an
easily
acces-
sible
location.
All
install-
er-supplied
parts
must
conform
to
local
codes
with
the
National
Electrical
Code,
ANSI/NFPA
70-1990
and
the
National
Fuel
Gas
Code,
ANSI
Z21.58D-2002.
The appliance
and its individual
shut
off valve
must
be discon-
nected
from
the
gas
supply
piping
system
during
any pres-
sure
testing
of
that
system
at
test
pressures
above
1/2"
PSIG
(3.SKPA).
The
appliance
must
be isolated
from
the gas supply
piping
system
by closing
its in-
dividual
manual
shut off during
any pressure
testing.
Do not ap-
ply threading
compound
to the
first two
pipe threads
as to avoid
clogging
of
the
burner
valves
and
orifice.
Do
not
put
sealant
on any male end of flare fittings.
For built-in
installations,
it is rec-
ommended
that anyflexible
pipe
used be kept
as short
as possi-
ble. For freestanding
units using
natural
gas, it is strongly
recom-
mended
that a quick
disconnect
kit
from
Lynx
be installed.
This
kit,
part
#LQD, is available
from
your dealer.
NATURAL
GAS
The installation
of the grill
must
conform
with
local
codes
or, in
the
absence
of
local
codes,
to
the National
Fuel Gas Code ANSI
Z21.58D-2002
or latest edition.
If
installed
in Canada,
installation
must
be in accordance
with
Gas
Code
CAN
/
CGA-B149.1/.2
and
local codes.
The
gas
supply
line
must
be
sized
to
accommodate
all
the
gas-fired
equipment
that
may
be
connected
to
that
supply,
i.e. total
BTU output
to
be con-
sumed, needs to be determined
Fittingsshown below are for a
typicd
installation and are not
supplied with the grill. As each
installation may require differ-
ent plumbing,
Lynx
recoznlnends
that this step be performed by
a qualified technician.
Male
to 3/4"
Female
elbow
NPT
to 3/4"
flare
fitting
Incoming
natural
as supply
pipe
Convertible
Regulator
--
supplied
with grill
(Gas
type
conversion
requires conversion
kit
-
contact
dealer for details)
J
3/4"
Min. Dia.
flexible
connector
Figu
re
8-1
-
Typical attachment
for
using
natural
gas.
Ghut-off
valve
8
I,-II-yNX
Sample