Ge AEH08FMG1 user manual download

You can view the full version and download it in PDF format.
Page 5 of 48
ge.com
Do Not Operate in Freezing Outdoor Conditions
This cool<rely
air
conditioner
was not designed
for
fleezing
outdoor
conditions.
It illust not be used in
fleezing
outdoor
conditions.
Remote
Control
To ensure
proper
operation,
aim
file
remora
conuol
at
the
signal
receiver
on
the
air
condifioneL
Tile remote
conuol
signal has a range
of
up m 20 feet.
Make sure riDdling is between
die air conditioner
and the remora
conuol
that could
block the
sigmal.
Make sure batteries
are flesh and
instaUed
correctly
_tsindicated
on the remora
conuol.
Cool Mode
Use file
Coolmode
at
Low,Med, High
or
AutoFan
Speed
for cooling. Use tile
Temperature
Increase
/
Decrease
pads to set tile desired
temperature
between
64°F and
86°F in 1°F increments.
An
electronic
fllemlostat
is used
to
maintain
file
room
temperature.
Tile
compressor
will
cycle
on
and
off
to
keep
file
room
at
file
set
level
of
comfort.
Set
file
themlostat
at
a lower
number
and
file
indoor
air
will
become
cooleL
Set
die
fllelInostat
at
a higher
number
and
file
indoor
air
will
become
wamleL
NOTE:
If theair
conditioner
is offandis thenturnedon
while
set
toa
Cool
setting
orif turnedfromafansetting
toa
Cool
setting,it
may
takeapproximately
3minutes
forthecompressor
to
start
and
cooling
tobegin.
CoolingDescriptions
ForNormalCooling--Select
the
Cool
mode and
High
or
Med
fan with a middle
set temperature.
ForMaximum Cooling--Select
tile
Cool
mode
and
High
fan with a lower set temperature.
ForQuieterandNighttimeCooling--Select
tile
Cool
mode
and
Low
fan
with
a middle
set
temperature.
Energy Saver Mode
Controls
tile fan.
ON--The
fan
will cycle on
and
offwidl
die
compressor.
This
results
in wider
variations
of room
temperature
and
humidity.
Normally
used
when
tile
room
is unoccupied.
NOTE:
The fan
may
continue to run
for a short time after the compressor
cycles
off.
OFF--The
tim
runs
all tile
time,
while
file
compressor
cycles
on
and
off:
Fan Only Mode
Use the
FanOnlyMode
at
Low,Medor Highfan
speed to provide
air circulation
and
filtering
without
cooling.
Since fan-only settings do not
provide
cooling, a Set mmperamre
camlot
be
enmred.
Tile room
mmpemmre
will appear
in tile displ W.
NOTE:
AutoFanSpeedcannotbeusedwhenin the
FanOnly
Mode.
Auto Fan Speed
Set to
Auto
fan speed
for tile fan speed
to
automatically
set
m
tile
speed
needed
m
provide
optimum
comfort
settings wifll tile set temperature.
If the room
needs
more
cooling, the fan speed
will automatically
incre_tse. If the room
needs
less
cooling,
the fan speed will automatically
decrease.
NOTE:
AutoFanSpeedcannotbeusedwhenin the
FanOnly
Mode.
Power
Outage Recovery
Feature
In
tile
case
of a power
outage
or
interruption,
tile
unit
will automatically
restart
in the
settings
last
used
after
tile
power
is restored.
If tile
Delay 1-24hr
feature
was set, it will resume
countdown.
You may
need
to set a new time if desired.
5
Sample