Frigidaire CRA074AT70 user manual download (Page 2 of 11)

Languages: English
Pages:11
You can view the full version and download it in PDF format.
Page 2 of 11
ThisUSE&CARE
MANUAL
provides
specific
operating
instructions
foryourmodel.
Use
theroomairconditioner
onlyas
instructed
inthisUSE& CARE
MANUAL.
These
instructions
arenotmeant
tocover
everypossible
condition
andsituation
that
mayoccur.
Common
senseandcaution
mustbepracticed
when
installing,
operating,
andmaintaining
anyappliance.
The power supply cord with
this air conditioner
contains
a current
detection
device designed to
reduce the
risk
of fire.
Please refer to the section 'Operation
of
Current
Device' for details.
tn the
event that
the power supply cord is
damaged,
it cannot
be repaired,
tt must be
replaced
with
a cord from the product
manufacturer.
Avoid fire hazard or electric shock. Do not
use an extension
cord or an adaptor
plug.
Do
not remove any prong
from the
power cord.
Grounding
type
wall
receptacle
Power supply cord
with 3-prong grounding
plug
and
current
detection device
For Your Safety
Do not store or use gasoline or other flammable
vapors and liquids
in the vicinity of this or any
other appliance.
Read product
labels for flammability
and other warnings.
Prevent
Accidents
To reduce the risk of fire,
electrical
shock, or injury
to persons
when using
your air conditioner,
follow
basic precautions,
including
the following:
Be sure the electrical
service is adequate
for the model you have chosen.
This information
can be found
on the serial plate, which
is located
on the side of the cabinet
and behind the
grille.
If the air conditioner
is to be installed
in a window,
you will probably
want to clean both
sides of the glass first, tf the window
is a triple-track
type with
a screen panel included,
remove the screen completely
before
installation.
Be sure the air conditioner
has been securely and correctly
installed
according
to the
separate
installation
instructions
provided
with this
manual.
Save this
manual and the
installation
instructions
for possible
future
use in removing
or reinstalling
this
unit.
When handling
the air conditioner,
be careful to avoid cuts from sharp metal fins on front
and rear coils.
Electrical
Information
The complete
electrical
rating
of your
new room air conditioner
is stated
on the serial plate.
Refer to the rating when
checking
the electrical
requirements.
,
Be sure the air conditioner
is
properly
grounded.
To minimize
shock and fire hazards,
proper
grounding
is important.
The power cord is equipped
with
a three-prong
grounding
plug for protection
against
shock hazards.
Your air conditioner
must be used
in
a properly
grounded
wall receptacle.
If the wall
receptacle
you
intend
to use
is
not adequately
grounded
or protected
by a time
delay fuse
or circuit breaker,
have a qualified
electrician
install
the
proper receptacle.
Do not run air conditioner
without
outside
protective
cover
in
place. This could result
in
mechanical
damage
within
the air conditioner.
.......
"
Do
not
use
an
extension
cord
or an adapter
PlUg-
......................................................................................
READ
THIS
SECTION
BEFORE
ATTEHPTING
TO
OPERATE
AIR
CONDITIONER,
Unit
must
be upright
for
one hour
prior
to operating.
Operation
of Current
Device
Plug
in &
press
RESET
2
The
power
supply
cord
contains
a current
device
that
senses
damage
to the
power
cord.
To test
your
power
supply
cord
do the
following:
1.
Plug
in
the
Air Conditioner.
2.
The
power
supply
cord
will
have
TWO
buttons
on the
plug
head.
Press
the
TEST
button.
You will
notice
a click
as the
RESET
button
pops
out.
3.
Press
the
RESET
button.
Again
you
will
notice
a click
as the
button
engages.
4.
The
power
supply
cord
is
now
supplying
electricity
to the
unit.
(On
some
products
this
is
also
indi-
cated
by a light
on the
plug
head).
,
Do not use this device to turn the unit on or off.
• Always make sure the RESETbutton
is
pushed
in
for correct operation.
The power supply cord must be replaced
if it
fails to reset when either the TEST button is pushed,
or
it
cannot be reset. A new one can be obtained
from the product manufacturer.
,
If power supply cord
is
damaged,
it
CANNOT be repaired. It MUST be replaced by one obtained
from the product manufacturer.
02009
Electrolux
Home
Products,
Inc.
All
rights
reserved.
Sample