Black & Decker CCS818 TYPE 1 user manual download

You can view the full version and download it in PDF format.
Page 1 of 2
RC800- INSTRUCTIONSHEET
Intended
use
The RC800
replacement
chain
has been specifically
designed
for
use with the CCS818
Cordless
Chain Saw and NPP2018
Cordless
Pole Saw.
z_WARNING:
Read all
instructions.
Failure to follow all
instructions
listed below may result in electric shock, fire and/or
serious injury.
SAVE THESE INSTRUCTIONS
Reduced
Kickback
Chain -
The RC800 chain is designed
with
a
contoured
depth gauge and guard link which deflect kickback force
and allow wood to gradually
ride into the cutter.
Z_WARNING:
Some dust created
by power sanding,
sawing,
grinding,
drilling, and other construction
activities
contains
chemicals
known to cause cancer,
birth defects
or other
reproductive
harm. Some examples
of these chemicals
are:
lead from lead-based
paints,
crystalline silica from bricks and cement and other masonry
products,
and
arsenic and chromium
from chemically-treated
lumber. (CCA)
Your risk from these exposures
varies, depending
on how often
you do this type of work. To reduce your exposure
to these
chemicals:
work in a well ventilated
area, and work with
approved safety equipment,
such as those dust masks that are
specially designed to filter out microscopic
particles.
• Avoid prolonged
contact
with dust from power sanding,
sawing, grinding, drilling, and other construction
activities.
Wear protective
clothing and wash exposed areas with soap
and water.
Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.
ZLWARNING:
Use of this tool can generate
and/or disburse
dust, which may cause serious
and permanent
respiratory
or
other injury.
Always use NIOSH/OSHA
approved
respiratory
pro-
tection appropriate
for the dust exposure.
Direct particles
away
from face and body.
z_WARNING:
Always
wear eye protection.
ZLCAUTION:
Wear appropriate
personal
hearing protection
during use. Under some conditions
and duration
of use, noise
from this product may contribute
to hearing loss.
Replacing
the
Saw
Chain
z_CAUTION:
Sharp chain.
Always
wear protective
gloves
when
handling
the chain.
The chain is sharp and can cut you
when it is not running.
_WARNING:
Sharp
moving
chain.
To prevent
accidental
operation,
insure
that battery
is disconnected
from
the tool
before
performing
the following
operations.
Failure to do this
could result in serious personal
injury.
• Place the saw on a firm surface.
Rotate the two allen head
screws (1) (on socket cover (2)) counterclockwise
with the
wrench (3) as shown
in figure
A.
• To remove the saw chain, rotate the tension adjustment
screw (4)
in the front of the housing using the flat screwdriver
end of the
wrench (3) as shown
in figure
B. Turning the screw
counterclockwise
allows the guide bar to recede and reduces the
tension on the chain so that it may be removed.
• Remove sprocket cover (2) and allen head screws
(1).
• Lift the worn saw chain out of the groove in the guide bar.
• Place new chain in groove of guide bar making sure saw teeth
are facing correct direction by matching arrow on chain with
graphic on housing shown in figure
C.
• Place the saw chain and guide bar assembly
around the sprocket
(5). Check to make sure that the slot (6) in the guide bar is over
the two location pins (7) shown in figure
D and that the hole
below the slot is located over the adjustment
pin (8).
• Replace sprocket cover (2) and
thread allen headscrews (1) in with
wrenchuntil snug, then
backwrenchoffonefull
turn.
• Pull bar nose up and keep it up as you adjust tension.
• Rotate the tension adjustment
screw (4) in the front of the
housing clockwise
to increase the chain tension.
• Follow
instructions
in "Adjusting
Chain Tension"
section
of
saw
manual.
• While still holding the bar nose up, securely tighten the rear allen
screw (1) first, then tighten the front allen screw.
• When the chain is new check the tension frequently
(after
disconnecting
battery) during the first 2 hours of use as a new
chain stretches
slightly.
Service
Information
Whether you need technical advice, repair, or genuine factory
replacement
parts, contact the Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory
under "Toots-Electric"
or call: 1-800-54-HOW TO (544-6986).
Black
& Decker
(U.S.)
Inc.,
701 E. Joppa
Rd,
Towson,
MD 21286
U.S.A.
Cat
No,
RC800
Copyright
© 2006
Black
& Decker
See 'Tools-Electric'
- Yellow
Pages
-
for Service
& Sales
Form
#623382-00
AUG.
'06
Printed
in China
Sample