Amana NDE2330AYW Installation Instructions download

Languages: English
Manual type:Installation Instructions
Pages:2
Instant delivery to e-mail
You can buy the full version and download it in PDF format instantly.
Page 1 of 2
BUILT BETTER $H_N
m$HAS $@ B__
Installation
Instructions
Electric
Dryer
Keep
instructions
for
future
reference.
Be
sure
manual
stays
with
dryer.
Questions?
See
Owner's
Manual
or
call
Amana
Consumer
Affairs
Department
1-800-843-0304
You'll
Need
a
Few
Things
Before
You
Begin
Power
Corot
(3-wire
or 4-wire)
and
StrftJn
Relief
Duct
Tape
Wrench
S crews
(
(_
({_)
(supplied)
Screw
Drivers
Level
_
J
REMOVE
PARTS
I
AND
CLEAN
DRYER
DRUM
Optional
Kits
Kits are available at extra cost through
your Amana dealer or
Amana factory 1-800-843-0304.
Directional
Exhaust
Kit
DK1 Sales Accessory
(Directional
Exhaust Kit #528P3).
Flexible
Metal Vent Kit
Exhausting the dryer in hard-to-reach
locations can be accomplished
by
installing
Kit # 521P3.
CONNECT
DRYER
TO
EXHAUST
SYSTEM
Secure all joints with clamps or duct
tape. DO NOT use sheet metal
screws or other fastening
means
which extend into the duct to attach
exhaust pipe joints. They could
catch lint and reduce the efficiency
of the exhaust system.
IMPORTANT:
Keep exhaust duct
as short as possible.
Be sure old ducts are clean before
installing your new dryer.
To prevent backdraft when dryer is
not in operation,
outer end of
exhaust pipe must have a weather
hood with hinged dampers
(obtain
locally).
Weather hood should be installed
at least 12" (30.5 cm) above the
ground. Higher clearances
may be
necessary
in areas where heavy
snowfall can occur.
No extra system length
consideration
is necessary when
exhausting
through the roof. Use
MAXIMUM
EXHAUST
LENG TH
table to calculate system length.
Use a roof cap that provides air
flow equal to weather hood.
Exhaust
Directions
Dryer can be exhausted
to the
outdoors through the back, left,
right or bottom of the dryer.
Dryer is shipped from factory ready
for rear exhaust.
No kits
required.
To exhaust dryer through sides or
bottom, install a DK1 Sales
Accessory
(Directional
Exhaust Kit
528P3). Available as optional
equipment
at extra cost.
Exhaust
System
Materials
Exhaust duct must be four inches
(10.2 cm) in diameter without
obstructions.
Rigid metal duct is
recommended.
Non-combustible
semi-rigid
flexible metal duct is
acceptable.
DO NOT use plastic pipe, foil pipe,
or flexible
plastic pipe, because it
contributes
to poor drying
performance
and collects lint, which
can lead to a fire hazard. To identify
flexible foil or plastic duct, pinch the
coils of the duct between your
fingers. If the coils can be brought
together, do not use the duct.
f
['se
Semirigid
Metalj
'_. Rigid Metal
Do
Not
_se
Maximum
Exhaust
Length
Number of
90° Elbows
0
1
2
3
Rigid Metal Duct
Weather
Hood
4-inch Opening
44 feet (13.4 m)
34 feet (10.4 m)
26 feet (7.9 m)
20 feet (6.1 m)
Weather
Hood
2½-inch
Opening
34 feet (10.4 m)
26 feet (7.9 m)
20 feet (6.1 m)
14 feet (4.3 m)
Number of
90° Elbows
0
1
2
3
Flexible
Metal Duct
Weather
Hood
4-inch Opening
24 feet (7.3 m)
20 feet (6.1 m)
16 feet (4.9 m)
12 feet (3.7 m)
Weather
Hood
2½-inch
Opening
20 feet (6.1 m)
16 feet (4.9 m)
12 feet (3.7 m)
8 feet (2.4 m)
NOTE:
Deduct 6 feet (1.8 m) for each additional
elbow,
Recommended
Weather
Hood
Recommended
for
Short
Runs
Only
4" d0.16 cm)
4"
(1{).16
cm)
2-1/2"
(6..35 cm)
CONNECT
ELECTRICAL
CORD
Access
,__
Cover
Strain
relief
/_
(not
supplied
with
dryer)
3-wire
or
4-wire
Plug Connection
Four-wire cord is required for mobile
homes or where codes do not permit
grounding
through neutral.
1.
Remove access
cover from rear of dryer.
2.
Use a strain relief and insert
end
of power cord through power supply
hole.
3.
Use the three screws from envelope
located in the drum to attach the
remaining
power cord wires to the terminal block as follows:
Red
wire
to "L1" terminal.
Black wire to '%2" terminal.
• White wire to Neutral terminal.
• 4-wire
Plug Only--Remove
ground screw and detach ground wire
from bulkhead.
Attach power cord ground (green) wire to rear
bulkhead using ground screw. Attach free ground wire, previously
attached with ground screw,
with white wire to the neutral (center)
terminal
on the terminal
block.
4.
Tighten all screws and reinstall access cover removed
in step 1.
3-wire
Cord
Installed
"LI"
Neutral
"L2"
White
Ground
SCreW
Red
4-wire
Cord
Installed
Ground
wire
!l tl
Neutral
(
i__
screw
Red
White
Black
Green
Black
POSITION
AND
LEVEL
DRYER
Place dryer in position, adjust all
legs (4) until dryer is level side to
side and front to back.
Level.
Part No.40086104
¢, 2000 Amana
Appliances
Printed
in US.A.
9/00
Amana,
Iowa 52204
Sample