Admiral AGD4475TQ1 Installation Instructions download (Page 4 of 20)

Languages: English
Manual type:Installation Instructions
Pages:20
Instant delivery to e-mail
You can buy the full version and download it in PDF format instantly.
Page 4 of 20
Mobile
Home
-
Additional
Installation
Requirements
This dryer is suitable
for mobile home installations.
The installation
must conform
to the Manufactured
Home
Construction
and Safety Standard,
Title 24 CFR, Part 3280
(formerly the Federal Standard
for Mobile Home Construction
and
Safety, Title 24, HUD Part 280) or the Canadian Manufactured
Home Standard,
CAN/CSA-Z240
MH.
Mobile home
installations
require:
Metal exhaust system hardware,
which is available for
purchase
from your dealer.
Mobile Home
Installation
Kit Part #346764. See "Tools and
Parts" section for information
on ordering.
Special provisions
must be made in mobile homes to
introduce
outside
air into the dryer. The opening (such as a
nearby window)
should
be at least twice
as large as the dryer
exhaust
opening.
Electrical
Shock
Hazard
Plug into
a grounded
3 prong
outlet.
Do not
remove
ground
prong.
Do not
use an adapter.
Do not
use
an
extension
cord.
Failure
to follow
these
instructions
can
result
in death,
fire, or electrical
shock.
A 120 Volt, 60 Hz., AC only, 15- or 20-amp,
fused electrical
supply
is required. A time-delay
fuse or circuit
breaker is
recommended.
It is recommended
that a separate
circuit
serving only this dryer be provided.
GROUNDING
INSTRUCTIONS
For a grounded,
cord-connected
dryer:
This dryer
must be grounded.
In the event of malfunction
or
breakdown,
grounding
will reduce the risk of electric shock
by providing
a path of least resistance
for electric current.
This dryer
is equipped
with a cord having an equipment-
grounding
conductor
and a grounding
plug. The plug must
be plugged into an appropriate
outlet that is properly
installed and grounded
in accordance
with all local codes
and ordinances.
WARNING:
Improper
connection
of the equipment-
grounding
conductor
can result in a risk of electric shock.
Check with a qualified
electrician
or service
representative
or personnel
if you are in doubt as to whether
the dryer is
properly
grounded.
Do not modify the plug provided
with the
dryer: if it will not fit the outlet, have a proper outlet installed
by a qualified
electrician.
SAVE
THESE
INSTRUCTIONS
Explosion
Hazard
Use a
new CSA
international
approved
gas supply
line.
install
a
shut=off valve.
Securely
tighten
all gas
connections.
(f
connected
to LP,
have a qualified
person make
sure
gas
pressure
does
not
exceed
13"
(33 cm)
water
column.
Examples
of a qualified
person
include:
licensed
heating
personnel,
authorized
gas
company
personnel,
and
authorized
service
personnel.
Failure
to do
so
can result
in death,
explosion,
or fire.
Gas Type
Natural
Gas:
This dryer is equipped
for use with
Natural gas. It is design-
certified
by CSA International
for LP (propane or butane) gases
with appropriate
conversion.
Your dryer must have the correct burner for the type
of gas in
your home. Burner information
is located on the rating plate in
the door well of your dryer. If this information
does not agree
with the type of gas available, contact
your dealer or call the
phone numbers
referenced on the front page of the Dryer User
Instructions.
LP gas conversion:
Conversion
must be made
by a qualified
technician.
No attempt
shall be made to convert the appliance from the gas
specified
on the model/serial
rating plate for use with a different
gas without
consulting
your gas company.
Gas Supply Line:
Must include 1/8"NPT minimum
plugged
tapping
accessible
for test gauge connection,
immediately
upstream
of the gas
connection
to the dryer. See illustration.
1/2"IPS pipe is recommended.
3/8"approved
aluminum
or copper tubing
is acceptable
for
lengths
under 20 ft (6.1 m) if local codes and gas supplier
permit.
If you are using Natural gas, do not use copper tubing.
Lengths over 20 ft (6.1 m) should use larger tubing
and a
different
size adapter
fitting.
If your dryer has been converted
to use LP gas, 3/8"LP
compatible
copper tubing
can be used. If the total length of
the supply
line is more than 20 ft (6.1 m), use larger pipe.
NOTE: Pipe-joint
compounds
that resist the action of LP gas
must be used. Do not use TEFLON ®ttape.
Must include a shutoff valve:
Sample