Kenmore 10654682300 Installation Instructions download

Languages: English
Manual type:Installation Instructions
Pages:2
Instant delivery to e-mail
You can buy the full version and download it in PDF format instantly.
Page 1 of 2
I
STRUCTIO
EET
For
"in the
Grill Filter" Water
Valve
ElectricalShock Hazard
Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death
or electrical shock.
g,
10.
11.
12.
NOTE:
Replace
the
unit compartment
cover
and reconnect
main
water supply.
Turn main water supply
on and check for leaks.
Flush the
water system.
Please
refer to the
"flushing
the
water system"
section.
Cycle dispenser
and icemaker.
Check for leaks and proper
operation
of dispenser
and icemaker.
Pictures
may vary from actual product.
STYLE
2
STYLE
I
FIGURE
1:STYLE
1
FILTER
INLET
TUBE
1,
2.
3,
4.
5,
(SHOWN
WITHOUT
MAINWATER
SUPPLY
LINE
CONNECTED)
Unplug refrigerator
or disconnect
power.
Turn off main water
supply
and disconnect
from
back of
refrigerator.
Gain access to unit compartment.
Remove
water
valve
assembly.
Disconnect
all tubing
and
electrical connections from water valve. If existing water valve
is the compression
nut style, all tube ends must be prepared
for insertion
into push-in fittings.
Please see "connecting
a
push-in
fitting" section.
If existing
water valve
has push-in
fittings, please see "disconnecting
a push-in fitting" section
for instructions.
Prepare
new water
valve
by removing
customer-connect
portion
from
original
main valve
body. Customer-connect
portion
of water valve
can be removed
by pulling
it away
from main water valve body. See
Figure
2.
CUSTOMER-CONNECT
PORTION
)FWATER
VALVE.
REATTACH
WITH
NEW
WATER
VALVE
FIGURE
2:
SEPARATED
WATER
VALVE
BRACKET.
6.
Install water lines into new water valve by pushing tubing into
the proper fittings. Make sure the tubing is pushed completely
into the fittings.
Please
see
"connecting
a push-in
fitting"
section
for instructions.
If required,
kit contains
extra
1/4"
tubing and coupling.
7.
Connect
wiring
harness
to new
water
valve.
If existing
water
valve
is compression
nut
style,
the
harness
may
need to be rerouted
to reach
the electrical
connections
on
the new water valve.
Rerouting harness
is accomplished
by
disconnecting
9-pin connector
and ground
connection
near
water valve. Then route harness on backside of suction tube
and reconnect
9-pin connector
and ground
connection.
8.
Align customer
connect
bracket holes to new valve bracket
holes. Mount new water valve and customer
connect where
existing
water valve was removed
in step 4.
@Whirlpool
Corporation
2011
(All Rights
Reserved)
1,
2.
3.
4.
5,
6,
7.
8.
9.
10.
NOTE:
FIGURE
3:STYLE
2
Unplug refrigerator
or disconnect
power.
Turn off main water supply.
Gain access to unit compartment.
Remove
water
valve
assembly.
Disconnect
all tubing
and
electrical
connections
from
water
valve.
For instructions
on how to remove
tubing from a push-in fitting, please see
"disconnecting
a push-in fitting" section.
Install water lines into new water valve by pushing tubing into
the proper fittings. Make sure the tubing is pushed completely
into the fittings. See "connecting
a push-in fitting" section for
instructions.
Connect
wiring harness to new water valve.
Mount new water valve where the existing water valve was
removed
in previous step.
Turn on water supply
and inspect for leaks.
Flush the
water system.
Please
refer to the
"flushing
the
water system"
section.
Cycle dispenser
and icemaker.
Check for leaks and proper
operation
of dispenser
and icemaker.
Pictures
may vary from actual product.
Flushing
the water
system
Use a sturdy
container
to depress
the water dispenser
bar until
the water begins to flow. Flush the water system
by dispensing
and discarding
2 to 3 gal. (8 to 12 L) of water. Cleaning the system
wilt take approximately
6 to 7 minutes and wilt help clear air from
the line. Additional
flushing may be required in some households.
Connecting
a
push-in
fitting
For a proper
seal,
all tube
ends inserted
into a push-in
fitting
must be round and free from surface
damage.
Tube ends can
be prepared
by cutting damaged
or deformed
areas from end of
tube. Tubing
must be cut square with
no burrs
or sharp edges
on tubing surface. Whirlpool
tubing cutter, part number 2255148,
recommended
for cutting tube.To insert, push the tube firmly into
the push-in
fitting
until the tube contacts
the tube stop. When
inserting the tube, one will encounter
some resistance
when the
tube contacts the o-ring seal. Push the tubing through
the o-ring
seat until the tube contacts the tube stop. Pull on the tube firmly
to verify it is secure. Turn on the water and check for leaks.
Disconnecting
a
push-in
fitting
Shut off the water
supply
and depressurize
system.
Push the
collet (gripper)
firmly
against
the fitting
and pull the tube away
from the fitting.
Instruction
Sheet
W10406282
Rev. A
03/11
Sample