Electrolux E23BC78IPS1 Installation Instructions download

Languages: English
Manual type:Installation Instructions
Pages:3
Instant delivery to e-mail
You can buy the full version and download it in PDF format instantly.
Page 1 of 3
Installation
Instructions
for
_Please
refer
to
your
Use
_t Care
Ouide
for
more
details.
Pro
arin
For Installation
Be sure to coordinate site preparation and installationwith your kitchen
contractor.
Includethese minimum guidelines in your site preparation:
®
®
®
®
®
®
Chooseaplace near agrounded electrical outlet.
Do not usean extension cord or an adapter plug.
Avoid direct sunlight and close proximity to a range,dishwasher or
other heat source.
Floorshould be leveland able to support afully loaded refrigerator.
Therefrigerator's Ice& Water Dispenser
requires water supply access.
Planfor easyaccess to counter tops when
removing food.
For complete access to drawers and freezer
baskets,doors must be ableto fully open.
Load refrigerator from side of cabinet only.
Do not run retainingstraps over handles nor over-tighten straps.
Never use refrigerator handles to movethe refrigerator.
Allow the following clearancesfor easeof installation, proper air circulation, and
plumbing and electrical connections: Sides & Top:3/8 inch
/
Rear:1inch
ConnectWater
Su
I
Before
Installing The WaterSupplyLine, YouWill
Need:
,
BasicTools:adjustablewrench, flat-blade screwdriver,
TM
and Phillips
screwdriver
*
Accessto a household cold water linewith water
pressure between30 and 100 psi.
A water supply line made of 1Ainch OD,copper or
stainless steel tubing. Todetermine the length of tubing
needed,measurethe distancefrom the icemaker inlet
valve at the back of the refrigerator to your cold water
pipe. Thenadd approximately 7 feet, so the refrigerator can be moved out for cleaning.
A shutoff valve to connect the water supply line to your household watersystem. DONOT usea self-
piercing type shutoff valve.
.
A compressionnut andferrule (sleeve)for connectingacopperwatersupplylineto the icemaker inletvalve.
French
Door
Bottom
Freezer/Refrigerator
ToConnect
WaterSupply
Line To
IceMaker
Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Placeend of water supply lineinto sink or bucket.
TurnON water supply and flush supply line until
water isclear.Turn OFFwater supply at shutoff valve.
3. Removeplastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass compression
nut, then ferrule (sleeve)onto water supply line.
Pushwater supply lineinto watervalve inlet asfar
as it will go (1Ainch). Slide ferrule (sleeve)into valve
inlet and finger tighten compression nut onto valve.
Tightenanother half turn with a wrench; DONOT
over tighten. See Figure 1.
Ifyou usestainlesssteeltubing - Thenut and
ferrule arealreadyassembledon the tubing. Slide
compression nut onto valve inlet and finger tighten
compression nut onto valve.Tightenanother half turn
with awrench; DONOTover tighten.
See
Figure 2.
5. Withsteel clamp and screw,securewater supply line
(copper tubing only) to rearpanelof refrigeratoras
shown.
6. Coilexcess water supply line (copper tubing only),
about 21/2
turns, behind refrigerator as shown and
arrangecoils so they do not vibrate or wear against
anyother surface.
7. TurnON water supply at shutoff valve and tighten
connections that leak.
steei
\\
past
c Water
Tub
a
u
/_/_
Clamp
\\
to
ice
Maker
_[
_
II
\_FiliTube_
II,,
II
Brass
\_
-
,u,//
IICompression
;
pp
///
moylng
refrigerator
out
for
cleaning.)
Figure 1
8,
9.
Reconnect refrigerator to electrical power source.
Toturn icemaker on, lower wire signal arm (side
mounted) or set the icemaker's On/Off power switch
to the 'T' position (rear mounted).
3
Level
Refrigerator & Adjust
)oors
(if necessary)
Guidelines
for
final
positioning
of
your
refrigerator
*
All four corners of the cabinetmust restfirmly on
floor.
*
Thesides should tilt 1Ainch from front to back (to
ensure that doors close and seal properly).
*
Doors should align with each other and be level.
Most
ofthese conditionscan
be met by
raising or
lowering
the
adjustable front
rollers,
To
level
the cabinet
using
the
front
rollers:
1
Youcan raise or lower eachdoor. Use a_/_inch
;ket
wrench to turn the adjustment screws (1 perside).
Toraise: turn adjustment screw clockwise.
Tolower: turn adjustment screw counterclockwise.
Ensure both doors are bind-free with their seals
touching the cabinet on all four sides and that cabinet is
stable.
After unit is leveled, lower anti-tip leg until it contacts
the floor.
°
Boor
Boor °}°
DO NOT REMOVE
this
label
until
the
refrigerator
has
been
leveled.
Please
follow
all
instructions
for
leveling
your
refrigerator.
Doors
final
adjustment
using
the
adjustable
lower
hinge
(select
models,
if
necessary):
1
Open doors to 90 degrees.
2
Remove screw.
3
Lift the door while adjusting the washer.
To raise the door: rotate washer clockwise.
To
lower
the door: rotate washer counter-clockwise.
4
Replace
the screw, ensuring
it is
between the spokes of the hinge washer.
Screw will not be
tight, just
insert
until
it is
flush with the hinge.
Bottom
of Door
Raising/Lowering Door
4
Leveling
Freezer
Drawer
(if
necessary)
t.
2.
Push Against
I
Freezer
Drawer
I
4.
ii
5.
I_
6.
A
I
II B
5
Remove
Internal
Shi
zn
.................................................
Electrolux
uses packing foam and tape to secure the
internal
parts of your refrigerator
for
shipping. Once the refrigerator
is in
position, you can remove this material.
Remove
Screw
Check gasket seal around
top,
bottom, and sides of freezer drawer.
If gasket is not sealed, open drawer
and slightly loosen 4 drawer screws
(2 on each side) to allow drawer to
rotate.
Close drawer and recheck the seal
on the gasket
(A). Open the drawer
grabbing by the sides in the center
(B). Be careful not to rotate the
drawer.
Tighten 4 drawer screws.
Recheck gasket seal.
Install the toe grille by fitting into
place.
What's
Next?
Congratulations!
You are ready to begin
enjoying
your new Electrolux
refrigerator.
,
For important
safety instructions
and to learn how to operate
your refrigerator,
please read
the
entire
Use & Care Guide.
,
You may want to start with the "Normal Operating
Sights & Sounds" section of the Guide to
learn what to expect during typical operation.
Please register your product. You can register online at www.electroluxappliances.com,
or
you can simply
send in the Registration
Card.
[]Installation
Check
List
Doors
[]
Handles are secure and tight
[]
Door seals completely to cabinet on all sides
[]
Fresh food doors are level
[]
Refrigerator
is level, side to side and tilted
1/4" front to back
[]
Toe grille is properly attached
to refrigerator
[]
Cabinet is sitting solid on all corners
Electrical
Power
[]
House power turned on
[]
Refrigerator
plugged
in
Ice
Maker
[]
House water supply connected
to
refrigerator
[]
No water leaks present at all connections
[]
Ice Maker is turned
ON.
[]
Ice & Water Dispenser
operates
correctly
[]
Select "Water" and fill a glass of water.
Final Checks
[]
Shipping material
removed
[]
Fresh Food and Freezer temperatures
set
/f
you are
not
satisfied
with
the installation
of your
refrigerator,
please
contact
the store
you purchased
it
from
or call
1-877-435-3287
for assistance.
P/N:
241940501
Sample
This manual is suitable for devices