- Repair manuals
- Laptops
- SONY
- VGN-BX
- Disassembly and assembly instructions
SONY VGN-BX Disassembly and assembly instructions download (Page 5 of 42)
Checkout
Languages: | English |
---|---|
Manual type: | Disassembly and assembly instructions |
Pages: | 42 |
Instant delivery to e-mail
You can buy the full version and download it in PDF format instantly.
Page 5 of 42
BX Series
Confidential
Cover (Memory), Memory
1)
1.MS-1-D.5
Remove the screw.
Screw:B7
Remove the Cover (Memory) while disengaging the detent (two places).
2)
3)
Outspread the tabs (arrow 1), and pull out the Memory diagonally upward
(arrow 2).
*When two Memory are installed, remove the other side of the Memory in
the way as above.
1
2
Memory
1
This manual is suitable for devices
1.MS-1-D.1 Confidential
Chapter 1. Disassembly & Assembly Guide
1-3. Disassembly & Assembly
- Main Section -
MS-1 Main Section Disassembly
BX Series
1.MS-1-D.2 Confidential
Battery Pack
Battery Pack
1) 2)
Lock Lever Release Lever
Slide the Lock Lever to the UNLOCK side.
Slide the Release Lever to the right side,
and turn over the Battery Pack to the rear side then remove it.
BX Series
1.MS-1-D.3 Confidential
2)
HDD
HDD
1)
Screw:B20 Remove the HDD.
Remove the screw.
BX Series
1.MS-1-D.4 2) Confidential
Holder (HDD) Insulator (HDD)
Parts of the HDD
1)
Screw:B13
HDD
Remove the three screws, and remove the HDD from the Holder (HDD). Peel off the Insulator (HDD).
3)
Holder (HDD)
Door (HDD)
Remove the Door (HDD) while disengaging the detent (two places).
BX Series
1.MS-1-D.5 Confidential
Cover (Memory), Memory
1) 2)
Screw:B7
Remove the screw. Remove the Cover (Memory) while disengaging the detent (two places).
3)
2
1 1
Memory
Outspread the tabs (arrow 1), and pull out the Memory diagonally upward BX Series
(arrow 2).
*When two Memory are installed, remove the other side of the Memory in
the way as above.
1.MS-1-D.6 Remark Confidential
Optical Disc Drive, Screws Screw:B19
(Special screw)
1)
Optical Disc Drive
Lever When there is a screw in the position of figure, remove
Push the lever once and pull out it in the direction the Optical Disk Drive after removing the screw.
of the arrow, then remove the Optical Disc Drive.
2)
Screw: Red-B2 / Blue-B11 / Green-B5
Remove the 12 screws.
BX Series
1.MS-1-D.7 Confidential
Hood (Keyboard)
1) 2)
Rubber (Screw) Screw:B3
Keyboard
Keyboard
Peel off the Rubber (Screw) (two places). Remove the two screws.
3) 4)
Hood (Keyboard) FFC
Turn over the Hood (Keyboard) to the rear side.
* The detents (10 places) are engaged. Harness
Disconnect the FFC and the Harness.
*FFC --- Slide the lock lever upward and release the lock.
Harness --- Pull out it upward.
BX Series
1.MS-1-D.8 Confidential
FFC
Parts of the Hood (Keyboard) -1
1) 2)
Kapton Tape 1st Model 4 [MA]
Kapton Tape
Peel off the Kapton Tape. Disconnect the FFC (two places).
*1st Model --- Five places *Slide the lock lever in the direction of the arrow, and release the lock.
Other --- One place
4)
3)
Harness
Screw: B4 SWX Board
Remove the four screws and the SWX Board. Disconnect the Harness.
BX Series
1.MS-1-D.9 Confidential
Parts of the Hood (Keyboard) -2
5) 6)
Screw: B11
IFX Board
Remove the two screws and the IFX Board. FFC
Disconnect the FFC.
*Slide the lock lever in the direction of the arrow and release the lock.
7)
Remark 4 [MA]
2nd Model
Screw: B4
Double Side Tape FFC
SWX Board
The FFC is secured with double side tape (two places). Remove the two screws and the SWX Board.
BX Series
1.MS-1-D.10 Confidential
Screw: B5
Keyboard -1
1) 2)
Camera Model
Harness
Release the Harness from the detent (five places). Remove the three screws.
3) Keyboard 4) FPC
2
Rib
1
Rib Slide the lock lever in the direction of the arrow
and release the lock, then disconnect the FPC.
FPC
BX Series
Release the rib (two places) by sliding the Keyboard in the direction of
the arrow 1, and lift it from the front side lightly.
*Notice : The FPC coming from the Keyboard is connected with
Mother Board.
1.MS-1-D.11 Confidential
BX Series
Keyboard -2
5)
Lock Lever
FPC
Turn over the Keyboard to the front side, and disconnect the FPC.
*Slide the lock lever upward and release the lock.
1.MS-1-D.12 Confidential
LCD Section -1
1)
Screw: 1st Model - B4
4 [MA] 2nd Model - B3
Lug Terminal
Remove the one screw. 2nd Model 4 [MA]
* It secures the lug terminal.
2)
1st Model
Kapton Tape Kapton (FPC)
BX Series
Peel off the Kapton Tape.
*1st Model --- Three places
2nd Model --- Two places
1.MS-1-D.13 4 [MA] 4) Confidential
4 [MA] Kapton Tape
LCD Section -2 2nd Model
1st (Camera) Model
3)
1st Model
Coaxial Cable
Disconnect the Coaxial Cable (two places). Peel off the Kapton Tape.
* Disconnect it vertically.
5) 6)
Camera Model Harness
Harness
Disconnect the Harness upward. Disconnect the Harness upward and release it from
the detent (four places).
BX Series
1.MS-1-D.13(a) 4 [MA] Confidential
LCD Section -3
7) 8)
Screw: B21
1st (WAN (EXT)) Model
AL Foil (Hinge)
4 [MA]
LCD Section
Remove the four screws and LCD Section.
Peel off the AL Foil (Hinge).
BX Series
1.MS-1-D.14 Screw: Red: 1st Model - B8 Confidential
BX Series
Bracket (KB EX) 2nd Model - B30
Blue-B3
1) Green: 1st Model - B2
1st Model 2nd Model - B31
2) 4 [MA]
Bracket (KB EX)
2nd Model
Remove the screws.
*1st Model --- 8 places
2nd Model --- 12 places
Remove the Bracket (KB EX).
1.MS-1-D.15 Confidential
Palmrest 2)
1) Bluetooth Model
Screw: 1st Model - B10 Harness
4 [MA]2nd Model - B31
Turn over the Palmrest to the front side lightly
Remove the three screws. and disconnect the Harness (one place) vertically.
3) 4)
Palmrest
Felica Model
FFC
FFC Disconnect the FFC.
Then remove the Palmrest.
Turn over the Palmrest to the front side lightly and slide the lock lever
upward to release the lock. And then Disconnect the FFC.
BX Series
1.MS-1-D.16 2) 1st Model 4 [MA] Confidential
4 [MA] Heatsink INT Model
Heatsink -1
1) 1st Model
4 [MA]
Sheet (AL-Bracket Bay)
Peel off the Sheet (AL-Bracket Bay). Screw: Red-B3 / EXT Model
Blue-B8
3) 4 [MA] Remove the screws.
4) 4 [MA] *INT Model --- Three places
2nd Model EXT Model --- Five places
2nd Model
Heatsink
Heatsink
INT Model
Screw: Red-B3 / EXT Model Harness
Blue-B30 Disconnect the Harness.
Remove the screws.
*INT Model --- Four places
EXT Model --- Five places
BX Series
1.MS-1-D.16(a) 4 [MA] 6) 1st (EXT) Model 4 [MA] Confidential
Harness
Heatsink -2 Heatsink
5) Disconnect the Harness.
Heatsink
1
2
Lift the right side of the Heatsink and remove it in the direction
of the arrow 2.
BX Series
1.MS-1-D.17 [MA] Confidential
Harness
Fan 1st (INT) Model Disconnect the Harness.
1) 3 [CHG] 2)
Screw: Red-B15 / Blue-B24
Remove the two screws.
*Use a 4 mm socket wrench for B15.
3)
Fan
Remove the Fan.
BX Series
1.MS-1-D.18 Confidential
PC Card Connector, Guide (HDD)
1) 4 [MA] 2) 4 [MA]
Screw: 1st Model - B8
4 [MA] 2nd Model - B30 1st (INT) Model 2nd Model
Screw:B3
Connector
PC Card Connector Sink (Choke)
Remove the two screws, and remove the Sink (Choke).
Remove the screws, and remove the PC Card Connector
while disconnecting the connector.
* 1st (INT) Model --- Two places
Other --- One place
3)
Screw:B10
Guide (HDD)
Remove the three screws and the Guide (HDD).
BX Series
1.MS-1-D.19 2) Confidential
Harness
IFX-431 Board 1st Model
1) 4 [MA]
Harness
IFX Board Screw: 1st Model - B4
Disconnect the Harness (two places) vertically. 2nd Model - B3
3)
IFX Board
Remove the screws.
*1st Model --- Three places
2nd Model --- Two places
Remark
IFX Board Connector
Side B
IFX Board
Remove the IFX Board. Position of the Connector
*There is a connector on the rear.
BX Series
1.MS-1-D.20 2) 4 [MA] Confidential
Mylar (Bay Bracket)
4 [MA] 2nd Model
Bracket (ODD) -1
1)
Kapton Tape
Sponge 4 (Cooling UL)
1st Model
4 [MA]
Peel off the Kapton Tape (two places), and Peel off the Mylar (Bay Bracket).
Sponge 4 (Cooling UL) (1st model only).
3) 4) 4 [MA]
FPC Screw: 1st Model - B2 1st Model
4 [MA] 2nd Model - B33
Bracket
FPC
Slide the lock lever in the direction of the arrow to release the lock, Remove the two screws, and remove the Bracket and FPC.
and disconnect the FPC. * The Procedure of removing the Bracket is only for 1st Model.
BX Series
1.MS-1-D.20(a) 4 [MA] Confidential
BX Series
Bracket (ODD) -2
5)
Screw: Red-B4
Blue: 1st Model - B8
4 [MA] 2nd Model - B30
Bracket (ODD)
A
Remove the three screws. And remove the Bracket (ODD) while
taking out the A portion from under the Mother Board.
1.MS-1-D.21 2) 4 [MA] Confidential
Sheet (AL-DC Cable)
PWS-51 Board 2nd Model
1) 1st (WAN) Model Tape (Charger/B)
4 [MA]
PWS Board Mylar (FFC)
Peel off the Sheet and Mylar.
Peel off the Tape (Charger/B).
3) 4)
Screw:B3
Connector Connector
Harness
PWS Board Disconnect the Harness.
Remove the three screws and the PWS Board.
* There are connectors (two places) on the rear.
BX Series
1.MS-1-D.22 2) Confidential
Screw:B3
Modem Card 1st Model 4 [MA] INT Model
1)
Kapton Tape
Peel off the Kapton Tape. Remove the screws.
*INT Model --- Two places
EXT Model --- One place
3) 4)
Connector
Modem Card
Connector Disconnect the Harness. Harness
Remove the Modem Card. BX Series
1.MS-1-D.23 Confidential
2)
CPU
CPU
1)
Rotate the lock screw in a counter clockwise direction by 90 degrees, Remove the CPU vertically.
and release the lock. *Be careful not to bend the pins.
*Use a 4 mm flat-blade screwdriver.
BX Series
1.MS-1-D.24 Confidential
Detent
Escutcheon (Front), Speaker
1) 2)
Detent
Button (Wireless)
Escutcheon (Front) Escutcheon (Front)
Remove the Escutcheon (Front) while disengaging the detent (five places). Remove the Button (Wireless) while disengaging the detent (four places).
3) 4)
Bracket (Speaker)
Speaker
Remove the Speaker (two places). Speaker
Outspread both sides of the Bracket (Speaker) and remove the Speaker.
BX Series
1.MS-1-D.25 Confidential
Mother Board -1 Backside
Insulator (PCB)
1)
Screw: Red-B15 / Blue-B3 / Green-B16 / Brown-B18
Insulator (PCB)
1st Model
Turn over the Insulator (PCB) from backside, and remove the 12 screws. 2nd Model 4 [MA]
* There is a screw under the Insulator (PCB). (1st Model Only)
* Use a 4 mm socket wrench for B15 and B16.
* Use a 5 mm socket wrench for B18.
BX Series
1.MS-1-D.26 Confidential
Mother Board -2 3) AL Foil-1
2) 1st (WAN (EXT)) Model
FFC
4 [MA]
Slide the lock lever upward two release the lock Peel off the AL Foil-1.
and disconnect the FFC.
5)
4)
WAN (EXT) Model
WAN (EXT) Model
Kapton Tape
Copper Foil -2 Peel off the Kapton Tape.
Peel off the Copper Foil-2.
BX Series
1.MS-1-D.27 7) Confidential
Mother Board Connector Portion
Mother Board -3
6) 4 [MA] 2nd Model
Mother Board
Kapton Tape
Peel off the Kapton Tape (one place). Raise the Mother Board to the right side while
releasing the connector portion from the Housing.
8) Side-B of the Mother Board Insulator (PCB)
Mother Board 9) 4 [MA]
2nd Model
Mother Board
Harness (RJ45+RJ11) Harness
Turn over the Insulator (PCB), and disconnect the Harness Turn over the Mother Board toward the rear.
(RJ45+RJ11) in the direction of the arrow.
* Then remove the Mother Board. (1st Model) 4 [MA] * As the Harness is connected to the rear of the Mother Board,
be careful not to damage the Harness. BX Series
1.MS-1-D.27(a) 4 [MA] Confidential
BX Series
Mother Board -4
10) 2nd Model
Modem Card
Harness
Disconnect the Harness in the direction of the arrow.
*Then remove the Mother Board.
1.MS-1-D.28 Confidential
Guide Bay
Guide Bay Remove the Guide Bay.
1) 2) BX Series
Screw:Red-B4
Blue: 1st Model - B4
4 [MA] 2nd Model - B3
Remove the four screws.
3) 4 [MA] Guide Bay
2nd Model
Bracket (Push Button) ASSY
Remove the Bracket (Push Button) ASSY.
1.MS-1-D.28(a) 4 [MA] Confidential
Heat Spreader (ICH) ASSY 2nd Model
1) 2) Screw:B11
Heat Spreader (ICH) ASSY
Mylar (Spreader)
Peel off the Mylar (two places). Remove the two screws, and remove the Heat Spreader (ICH) ASSY.
BX Series
1.MS-1-D.29 2) Confidential
Sheet, Bracket, Harness 1st Model 4 [MA]
1) Kapton Tape 2nd Model
Sheet
Remove the Sheet. Kapton Tape
3) Peel off the Tape.
Screw:B4 *1st Model --- Two places
2nd Model --- One place
4)
Bracket
Lug Terminal Harness (RJ45 + RJ11)
Remove the two screws and the Bracket. Remove the Harness (RJ45 + RJ11).
BX Series
1.MS-1-D.30 Confidential
IFX Board
IFX-430 Board
Remove the IFX Board.
1) 2)
Screw:B3
Adhesive Tape
FFC
Remove the screw and peel off the FFC.
* Adhesive Tape is attached to the rear of the FFC.
3) 4)
Harness (DC Cable)
Bracket (DC) Remove the Harness (DC Cable).
Remove the Bracket (DC).
BX Series
1.MS-1-D.31 Confidential
Parts of the IFX-430 Board 2)
Side A
1)
FFC
1st Model
Slide the lock lever in the direction of the arrow to release
4 [MA] the lock, and remove the FFC.
Kapton Tape
Side A
Peel off the Kapton Tape.
BX Series
1.MS-1-D.32 Confidential
Escutcheon (Left), Escutcheon (Right)
1) 2)
Escutcheon (Left)
Disengage the detent (one place) while raising the Escutcheon (Left) lightly. Disengage the detent (three places) while shifting it
3) in the direction of the arrow with tweezers or the like.
* Then remove the Escutcheon (Left).
Escutcheon (Right)
Remove the Escutcheon (Right) while disengaging the detent (six places).
BX Series
1.MS-1-D.33 Confidential
Parts of the Escutcheon (Right)
1) 2)
Sutter (PCMCIA) A Portion Sutter (PCMCIA)
Shift the Sutter (PCMCIA) in the direction of the arrow Remove the Sutter (PCMCIA).
and remove it from A portion.
3) 4)
Sutter (PCMCIA) Rubber (Hinge-R)
Spring Remove the Rubber (Hinge-R).
Remove the Spring.
BX Series
1.MS-1-D.34 Confidential
Parts of the Housing (Bottom) -1 2)
Screw:B5
1)
Door (Docking)
Detent
2 Cover (Hook-L)
1
Raise the front side of the Door (Docking) disengaging the detent (two Remove the two screws and Cover (Hook-L).
places) (arrow 1), and remove the Door (Docking) in the direction of the
arrow 2. 4) 4 [MA] 2nd Model
3) Screw:B4
Screw:Red-B5 Cover (Hinge-L)
Blue: 1st Model - B5
Cover (Hook-R)
4 [MA] 2nd Model - B11
Remove the two screws and Cover (Hook-R). Remove the one screw.
BX Series
1.MS-1-D.35 Confidential
Parts of the Housing (Bottom) -2
5) 6)
Cover (Hinge-L) Cover (Hinge-R)
Remove the Cover (Hinge-L). Remove the Cover (Hinge-R).
7) 8)
Detent Hook (Battery-R)
Detent
Button (Battery-R) Remove the Hook (Battery-R).
Disengage the detent (four places), and remove the Button (Battery-R).
BX Series
1.MS-1-D.36 Confidential
Hook (Battery-L)
Parts of the Housing (Bottom) -3
9) 10)
Detent
Detent
Button (Battery-R)
Disengage the detent (four places), and remove the Button (Battery-R). Remove the Hook (Battery-L).
11)
Spring (Hook Battery-L)
Hook (Battery-L)
Remove the Spring (Hook Battery-L).
BX Series
Update History Confidential
[ADD]---Addition [DEL]---Deletion [CHG]---Change [COR]---Correction [MA]---Model Addition
Date Contents Version No.
2006.08.28 1.30
3 [CHG] Screw (Page 17)
2006.10.20 2.00
4 [MA] (Page 8,9,12,13,13(a),14,15,16,16(a),17,18,19,20,20(a),21,22,25,26,27,
27(a),28,28(a),29,31,34)
BX Series