Wilbur Curtis D1000GT Service Manual download

Languages: English
Manual type:Service Manual
Pages:12
Instant delivery to e-mail
You can buy the full version and download it in PDF format instantly.
Page 1 of 12
1
F
IND
OUT
MORE
ON
THE
WEB
.
WILBURCURTIS.COM
CAUTION: DO NOT
connect this brewer to hot
water. The inlet valve is
not rated for hot water.
CAUTION: Please use
this setup procedure
before attempting to use
this brewer. Failure to follow the
instructions can result in injury or the
voiding of the warranty.
ISO 9001 REGISTERED
C
WARNING
HOT LIQUID,
Scalding may occur.
Avoid splashing.
Important Safeguards/Conventions
Service Manual, D1000GT & D500GT Airpot Brewers
FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO WWW.WILBURCURTIS.COM
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance
should be performed by an authorized Wilbur Curtis service center.
Do NOT immerse the unit in water or any other liquid
• To reduce the risk of fire or electric shock, do NOT open top or rear panel. There are no user service-
able parts inside. Repair should be performed only by authorized service personnel.
Keep hands and other items away from hot parts of unit during operation.
Never clean with scouring powders, bleach or harsh implements.
Conventions:
WARNINGS – To help avoid personal injury
Important Notes/Cautions
Sanitation Requirements
Curtis G3 Brewers are Factory Pre-Set and Ready to Go… Right out of the Carton.
Following are the Factory Settings for your Airpot Coffee Brewing System:
Brew Temperature = 200°F
Brew Volume = Set to dispensing vessel requirements (2.2 liters)
Generally there will never be a reason to change factory programming. However, should you need to make
slight adjustments to meet your brewing needs, programming instructions are provided later in this manual.
System Requirements:
• Water Source
20 – 90 PSI.
Must have a minimum flow rate of
½
GPM (preferred flow rate is 1 gpm).
• Electrical: See attached schematic for standard model or visit www.wilburcurtis.com for your model.
Equipment to be installed to comply with applicable federal, state, or local plumbing/electrical codes having
jurisdiction.
SETUP STEPS
The unit should be level (left to right and front to back), located on a solid counter top. Connect a water line
from the water filter to the brewer. NOTE: Some type of water filtration device must be used to maintain a
trouble-free operation. (In areas with extremely hard water, we suggest that a sedimentary and taste & odor
filter be installed.) This will prolong the life of your brewing system and enhance coffee quality.
1. A 3/8” NPT x 1/4” Flare elbow has been supplied for water line connection. Use tubing sized sufficiently to
provide a minimum of ½
GPM.
2. Connect the unit to an appropriate electrical power circuit.
3. Turn on the toggle (STANDBY/ON) switch behind the unit. The heating tank will start to fill. When the water
level in the tank rises to the correct volume, the heating elements will energize automatically.
With GT brewers, there is no danger of element burnout caused by an empty tank.
4. The heating tank will require 20 to 30 minutes to reach operating temperature (200°F). This will be indicated
when the screen reads READY TO BREW .
5. Prior to brewing, dispense 12 ounces of hot water through the hot water faucet.
6. Brew a cycle of at least 12 ounces, to purge the water lines of any air that may be trapped after filling.
BREWING INSTRUCTIONS
1. Brewer should be ON (Confirm at rear toggle switch, then press ON/OFF button). Ready to Brew on screen.
2. Open lid on an empty airpot and place on deck, ready to receive coffee.
3.
Place a new filter in brewcone.
4.Pour ground
coffee into
brewcone.
6. Press
Brew
button.
W
ILBUR
C
URTIS
C
OMPANY
, I
NC
.
5. Position
brewcone
into brew
rails.
WILBUR CURTIS COMPANY
Montebello, CA 90640
Models Included
• D1000GT
NSF International requires the following water connection:
1.
A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for
cleaning underneath.
2.
In some areas an approved backflow prevention device may be required between the brewer and the water supply.
To avoid temperature
drop when first brewing
coffee into the airpot,
preheat the airpot with hot water.
• D500GT
Setup and Brewing, page 1 are
similar for both brewers. Otherwise
D500GT information starts on page 6
Sample
This manual is suitable for devices